KL RP-230/730 Base: Replacement Train Horn Base / Driver for Kleinn Model 220 / 230 / 730

  • Replacement Horn Base Driver for 230 and 730 Horn - Kleinn Automotive Accessories - KL RP-230/730 Base

KL RP-230/730 Base

$49.95
$49.95 $49.95

💳 Get it today, pay over time with Shop Pay Installments.

In stock
PROP 65 WARNING:
This product can expose you to chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

KL RP-230/730 BASE - REPLACEMENT HORN BASE FOR MODEL 220, 230, & 730 TRAIN HORNS

RESTORE STRUCTURAL INTEGRITY & OPTIMIZED FLUID AIRFLOW MANAGEMENT

Re-establish the maximum pneumatic flow and uncompromising structural durability of your train horn network with the premium Kleinn Replacement Horn Base Driver. As the mechanical backbone of your vehicle's high-decibel payload, this heavy-duty multi-port manifold manifold acts as the central hub of your system. It splits and balances incoming high-pressure compressed air fields, forcing high-volume flow paths evenly into your attached horn trumpets to secure peak acoustic resonance and long-term deployment authority.

PRECISION MACHINING & LEAK-FREE VEHICULAR RESILIENCE

The Model KL RP-230/730 Base is engineered specifically as an exact original equipment factory replacement block to handle under-chassis elements seamlessly. Precision-machined internal port configurations guarantee an air-tight seal, stopping systemic line leaks while maximizing localized pressure capacity. It serves as a direct drop-in refresh part for Kleinn Model 220, 230, and 730 triple and dual locomotive horn arrays, providing a cost-effective alternative to replacing an entire system when addressing localized thread fatigue or impact damage.

Why Choose the 230/730 Replacement Horn Base?

  • Universal System Compatibility: Tailored as an exact factory-spec driver for Kleinn 220, 230, and 730 high-performance train horn series.
  • Standardized 1/4" NPT Air Inlet: Built with a machined 1/4-inch National Pipe Thread supply port for delay-free mechanical connection straight to your active delivery lines.
  • Rugged Environmental Shielding: Cast and machined from exceptionally dense zinc alloy material to easily survive extreme under-car vibrations, moisture packs, and road grit.
  • Leak-Free Pressure Paths: Precision-threaded interior tracks ensure tight seals to safely keep the system charged at peak operational pressures.

THE VERDICT: The definitive solution for sealing your primary air path. The Model KL RP-230/730 Base couples factory fitment dimensions with heavy-wall structural composition to guarantee your locomotive system remains air-tight, properly balanced, and fully operational.

What's Included in the Box

  • Replacement Component: One (1) individual Kleinn Replacement Manifold Base Driver Block (SKU: KL RP-230/730 Base).

🔴 PRO TIP: Block out parasitic pressure loss and maximize system blast volume. When transferring your existing horn trumpets and the electronic solenoid valve into this new replacement manifold base driver block, verify all mating threads are clean and debris-free. Always apply a few drops of a premium liquid thread sealant compound like our genuine Kleinn JUICE across all threaded joints to form a permanent, vibration-resistant structural seal. DO NOT seal the area between the front and back plate of the driver.

PRODUCT SPECIFICATIONS

Feature Details
Part Number / SKU KL RP-230/730 Base
Component Classification Replacement Train Horn Base & Driver Hub Block
Primary Input Port Connection 1/4" Female NPT (National Pipe Thread) Air Supply Inlet
Structural Core Integrity Heavy-Duty Corrosion-Resistant Shockproof Material Matrix
Cross-System Compatibility Direct-fit drop-in factory replacement for Kleinn Model 220, Model 230, and Model 730 Train Horn Systems
Primary Functional Utility Distributes and manages compressed high-pressure airflow evenly across horn expansion pipelines while securing layout anchoring paths
Purchase Configuration Note Includes replacement manifold base block driver only. Bell trumpets, air fittings, electronic solenoid valves, and framing brackets are sold separately and must be transferred or replaced.
KL RP-230/730 Base: Replacement Train Horn Base / Driver for Kleinn Model 220 / 230 / 730

$49.95

Does it come with a warranty?

Kleinn Automotive Accessories Limited Warranty

Kleinn Automotive Accessories stands behind the quality and craftsmanship of our products. Our products are covered against defects in materials and workmanship when properly installed and used under normal operating conditions, subject to the terms below.

One-Year Limited Warranty

Unless otherwise specified, Kleinn Automotive Accessories products are covered by a 1-year limited warranty from the original date of purchase.

This warranty applies to the original purchaser and covers defects in materials and workmanship under normal use.

If a product is determined to have a covered warranty defect, Kleinn Automotive Accessories will, at its discretion, repair or replace the defective product or component.

What Is Not Covered

This warranty does not cover damage or failure resulting from:

  • Improper installation
  • Misuse, abuse, or improper operation
  • Use outside the product's intended application or specifications
  • Modification or alteration of the product
  • Accidents or physical damage
  • Electrical damage
  • Environmental damage or exposure
  • Normal wear and tear

Kleinn Automotive Accessories is not responsible for installation or removal charges, diagnostic fees, labor costs, vehicle downtime, loss of use, or other incidental or consequential expenses associated with warranty service.

Warranty Claims

To request warranty service, email warranty@kleinn.com with the following information:

  • A copy of your original sales receipt or proof of purchase
  • Your full name
  • Email address
  • Telephone number
  • A brief description of the issue

A Kleinn representative will review your claim and may first attempt to resolve the issue through technical support.

If the product needs to be returned for inspection, Kleinn will provide a Return Authorization (RA) number and return instructions. Products should not be returned without prior authorization.

Once received, the product will be inspected to determine whether the issue is covered under warranty. If a covered defect in materials or workmanship is confirmed, Kleinn will, at its discretion, repair or replace the defective product or component.

If inspection determines that the product does not have a covered warranty defect, the product may be returned to the customer, and the customer will be responsible for applicable return shipping costs.

This limited warranty gives you specific legal rights. You may also have other rights, which vary from state to state.

Kleinn Automotive Accessories
4045 N. Highway Drive, Tucson, AZ 85705
Tel (520) 579-1531

What's the returns policy?

How To Return An Item

Your item must be in its original unused condition to be returned, unless there is a manufacturer defect. You must return the item within 30 days of your purchase.

1. Please email support@kleinn.com to request a refund and we will assign you a Return Authorization #.

2. Mail your returned item to:
Kleinn Automotive Accessories
Returns Department
4045 N Highway Drive
Tucson, AZ 85705

3. Include in your package a signed letter stating the reason for your return and the original receipt.

Return Non-Exceptions

Merchandise that has been worn, used, or altered will not be accepted for return or exchange.

Restocking Fee

All returns are subject to a 15% restocking fee, which will be deducted from your refund. If shipping and handling fees were applied to your order, they are non-refundable.

Customer Reviews

4.86 ★ (335)
Verified